Today I put a lot of time in getting the tank hidden.

A couple of things I may have done differently now that I’ve gotten this far. For one, the couch I ordered is a magic bed. Its sort of a hide-a-bed but with some minor differences. The reason I chose this couch is because its supposed to be the most comfortable bed when opened up. Only problem is this type cannot have anything put underneath it. So the tank had to set behind.

In this case, I should have made the tank taller and more narrow to take up less floor space. I made it this size because the tank sensor I had on hand limited the height to 13″. I could have gotten a second sensor and stacked them. The SeeLevel gauges lets you do that. In hindsight, I wish I would have made the tank more narrow. I could have gained about 6″ or so of floor space.

So now you know, the reason I ended up with this rather large cabinet in the front. As they say hindsight is 20/20. I’ll do the next one better :-).

I ended up laminating a top to match the rest of the trailer, and left an opening in the middle for storage.

To access the plumbing valves and the fuse holder, I made these small acess panels.

The entire counter top comes off with four screws from the top side. So If I really need access its not that difficult.

That’s it for today. Enough really. Tomorrow I plan on cleaning out the trailer all its tools and boxes and getting it ready for Monday….. …the polishing begins….

by

Nothing glamorous today in the art of vintage restoration.

Just trying to frame in the fresh water tank to hide everything, yet provide access when needed to the pump and fuse box.

Here’s what I came up with so far.

You’re probably saying interesting… I wonder how it will turn out.

I’m saying the same thing :-).

by

It took all day, but its done. Three trips to the hardware store for pluming parts…. which is in-line with my average.

First off I filled the tank to check for leaks.

Looks ok, so on to the inside. Here is the completed shot.

Now we’ll zoom in on the fill side. I thought this 1-1/2″ ID poly pipe would be the best for the fill side. It turns out it won’t bend w/o completely kinking. So I ended up with a couple of extra right angles. I really don’t like this for a solution. So I’ll keep my eye out for some more flexible pipe so I can have a straight shot. If you know of something better let me know.

The smaller hose is the air vent for the tank.

Next is the output side. There is a lot going on here. I added two 3-way selector valves so I can do a couple of things. First off, I can fill the tank from the city water input side. All I have to do when we are hooked up to city water is turn the selector knob on the wall and it will divert city water into the top tank connection.

The second selector chooses the pump input. In the normal position the pump input is connected the the tank. Pumping water on demand. The other position goes to a stubbed out connection where I can hook up a short hose that will go in a RV antifreeze bottle for winterizing.

And finally there is the standard drain valve for draining the tank.

Amazing how this took all day. But such is the life with vintage trailers.

Next up, hiding this mess behind a shelf before the couch gets here….

by

I don’t mean leaks…. I’m talking about a water fill for the fresh water tank.

I was trying to find a nice way to add this since I removed the original spigot used in the presureized system of 1960.

Since I’m using an on-demand pump, I also need an air vent for the tank. My research found marine parts to be the right fit. They are stainless steel and polished so they match the trailer great.

The picture below shows the water filler. Its called a marine deck fill and it is actually labled *Water* on the face. They also make them for fuel and waste as well.

The air vent is a stainless steel marine fuel tank vent. Its a screened vent with a splash gaurd. And it looks cool too.

Both items I found on eBay, but you can also find them a good marine supply houses.

Next came drilling the holes. Of course both pieces are different sizes than anything else I installed so I ended up having to buy two new hole saws. The lower hole just missed a cross support :-). Note to self… keep a better eye on those rivet lines….

Here they are installed and ready to go.

Here’s the final shot with the fill cover off. It uses a special *key* to open it. However a nice pair of needle nose pliers works in a pinch. Still it will keep those pesky trouble makers out.

Tomorrow I hope to finish up the fresh water tank installation. I need to find a 1-1/2″ male pipe thread to barb fitting so I can use a 1-1/2″ I.D. fill hose.

Those hardware store folks should know me by name….

by

Once again I didn’t like the way something turned out so I ripped it out and started over.

I thought the foam was too thick and I did not like the way it finished off toward the top. So I picked up some thinner foam and some oak trim and started again.

I’m much happier with this look.

Here is a shot of the new fresh water tank from All-Rite, an Ambassador Contributor. I’m still waiting on the fresh water fill I purchased on eBay before I can get this thing installed. It just over 30 gallons.

That’s it for now. Stay tuned…

by

One of the International options was padded material on the walls near the twin beds. These helped you keep away from the cold wall at night. They also added a touch of class only the International trim package could offer.

Again, I’m doing this in matching fabric. I cut a backer board 13″ and added some foam and fabric and there ya go.

One minor miss calculation. How to attach it to the wall.

I ended up pulling the bottom half of the material off. Then I directly screwed the backer board to the wall and then pulled the material tight and screwed it in at the bottom. The bottom half will be covered by the twin mattress.

Turned out pretty good. Just one more to go…

by

I picked up four leg-o-matic chairs that are from the 50’s. They suit the trailer well. The seats are pretty well worn as is the wood. Time to get to work.

I was able to get some new foam and I also ordered matching fabric for the gaucho we purchased. Cutting foam is a difficult chore until you learn the secret. An electric carving knife. I picked this one up from Walmart for $3. Worth it for sure. Cuts foam like butter.

Next was just removing the old and installing the new. Here is the seat going together.

I also restored the wood with Howards Restore-A-Finish. Same stuff I used on the cabinetry in the trailer.

And the final glamor shot in the trailer….

Thats all I had time for today. I have enough material to go against the wall near the twin beds, just like the Internationals came with…. Sorry Rob… 🙂

by

The custom made curtains for the trailer arrived today. Of course I could not wait to hang them to see how they look. And they look great!

These were made for us by Silver Threads Custom RV Interiors on the forums. She did a great job.

The green curtains pictured are the originals from 1960, and the others were made by someone along the way. They were ill fitting and not our first color choice.

Here are the new ones. They all fit perfectly. I still need to put up one more set, but they look great.

Great job from Silver Threads!

by

Did not have much time today to work on the trailer.  I decided to get the Shurflo water pump installed and start preping for the fresh water tank.

Here are the items Shurflo contributed to the project.  An Extreme Series Smart Sensor 4.0, a pre filter, and silencing kit.

I just layed it out and ran the water pipe that I had waiting for it into place.

The relay actually powers the pump so that I can use the switch that is on the SeeLevel gauge to turn it on.  Works great.

Here’s another view of the install.

Pretty much just like it was originally with the water tank up front under the window and the water pipe running along the street side wall.  I’ll add a little trim to hide it.

The couch will sit in front of the water tank.  I’m now designing the custom water tank and expect to have it built next week.  I’m thinking of going with 13″ x 12″ x 45″.  This will be a 30 gallon tank.  The formula to find out how many gallons is:

0.00432900431 * (13 * 12 * 45) = 30.3896103

Just substitue your tank demensions to find the gallons.  So now I’m in search of a water fill and water tank vent that can go on the side of the trailer.  These will dictate the fittings I’ll need to order for the tank.

by

I only had couple of hours today to work.  I went ahead and stained the bunk bed parts and reinstalled them.

I still need the wall brackets shown in the post below as well as the roof latches.

I have new curtains being made and noticed a few of my curtain rods have a lot of surface rust.  So I pulled them down today.  I’ll have to stop off at the hardware store, all too common of a practice, and get some paint to match as best I can.

Too bad they are not aluminum, or I’d just strip the paint and leave them.

by